Autoplay
Autocomplete
Previous Lesson
Complete and Continue
Cargo Drone Technical Course
Module 1 - Course overview
Welcome (0:21)
Course Info & Syllabus (3:33)
Introductions
Module 1 Discussion: Q&A
Module 2 - Understanding the M600Cargo
Module 2 Overview (1:12)
2.1 Camera drone vs Cargo drone (3:02)
2.2 About the M600 - Features and limitations (6:36)
2.3 M600C Hardware overview and equipment list (5:41)
2.4 M600C Cargo extension overview (5:47)
2.5 M600C Communication architecture (2:43)
2.6 M600C Control modes (4:02)
2.7 M600C Precision landing (2:08)
2.8 M600C Emergency plan (1:34)
Module 2 Discussion
Module 3 - M600C Drone Configuration
Module 3 Overview (0:47)
3.1 Hardware setup - How to connect the cargo extension to the drone (1:49)
3.2 Hardware setup - How to add a serial cable to the drone (2:15)
3.3 Hardware setup - How to electrically connect the cargo extension to the drone (0:40)
3.4 Hardware setup - How to power on and off the cargo extension (1:29)
3.5 Hardware setup - How to mount the cargo loading box (2:23)
3.6 Firmware configuration - How to select Non-DJI batteries (1:43)
3.7 Firmware configuration - How to adjust drone parameters in DJI Assistant 2 (3:02)
Module 3 Discussion
Course Assignment #1
Module 4 - Android Cargo Groundstation Application and Tablet Features
Module 4 Overview (1:33)
4.1 Cargo Groundstation Overview (6:59)
4.2 How to install the android cargo groundstation application (2:59)
4.3 How to use the android cargo groundstation application and start a mission (8:44)
4.4 Config file (JSON-format) for the android groundstation application (1:36)
4.5 How to load a cargo mission file to the android cargo groundstation application (2:04)
4.6 How to access the logs from the android cargo groundstation application (1:18)
4.7 How to get the IP address of the cargo extension on the drone using an android tablet (1:07)
4.8 How to access the cargo onboard controller file system using an android tablet (1:33)
4.9 How to upload a cargo mission file from the tablet to the onboard cargo extension (1:06)
4.10 How to access the logs of the cargo extension on the drone (0:49)
4.11 How to adjust the country-specific operator identifier of the APN network for the 4G module (1:47)
4.12 How to configure settings for the web server (1:34)
Module 4 Discussion
Course Assignment #2
Module 5 - Mission Planning
Module 5 Overview (1:02)
5.1 Route Planning Introduction (2:49)
5.2 Determining route, waypoints and safe landing locations (4:22)
5.3 QGroundControl Reference Guide
5.4 Mission planning with QGroundControl - Dummy mission (11:52)
5.5 Mission planning with QGroundControl - Real-world mission (9:22)
5.6 Mission planning with QGroundControl - Adjusting mission parameters (3:51)
Module 5 Discussion
Course Assignment #3
Module 6 - Standard Operating Procedures
Module 6 Overview (1:08)
6.1 Pack list - Let's go flying! (3:43)
6.2 Piloting the drone using the DJI Remote Controller (3:17)
6.3 Piloting the drone using virtual joysticks (4:09)
6.4 Mount the cargo box in the field (1:39)
6.5 Mount and test the precision landing setup in the field (3:18)
6.6 Checklist before flying a mission (3:02)
6.7 SOP - Run a Cargo Mission (8:20)
6.8 Failure handling
Module 6 Discussion
Course Assignment #4
Course Evaluation
We welcome your feedback
4.7 How to get the IP address of the cargo extension on the drone using an android tablet
Lesson content locked
If you're already enrolled,
you'll need to login
.
Enroll in Course to Unlock