Autoplay
Autocomplete
Previous Lesson
Complete and Continue
Cargo Drone Technical Course
Module 1 - Course overview
Welcome (0:21)
Course Info & Syllabus (3:33)
Introductions
Module 1 Discussion: Q&A
Module 2 - Understanding the M600Cargo
Module 2 Overview (1:12)
2.1 Camera drone vs Cargo drone (3:02)
2.2 About the M600 - Features and limitations (6:36)
2.3 M600C Hardware overview and equipment list (5:41)
2.4 M600C Cargo extension overview (5:47)
2.5 M600C Communication architecture (2:43)
2.6 M600C Control modes (4:02)
2.7 M600C Precision landing (2:08)
2.8 M600C Emergency plan (1:34)
Module 2 Discussion
Module 3 - M600C Drone Configuration
Module 3 Overview (0:47)
3.1 Hardware setup - How to connect the cargo extension to the drone (1:49)
3.2 Hardware setup - How to add a serial cable to the drone (2:15)
3.3 Hardware setup - How to electrically connect the cargo extension to the drone (0:40)
3.4 Hardware setup - How to power on and off the cargo extension (1:29)
3.5 Hardware setup - How to mount the cargo loading box (2:23)
3.6 Firmware configuration - How to select Non-DJI batteries (1:43)
3.7 Firmware configuration - How to adjust drone parameters in DJI Assistant 2 (3:02)
Module 3 Discussion
Course Assignment #1
Module 4 - Android Cargo Groundstation Application and Tablet Features
Module 4 Overview (1:33)
4.1 Cargo Groundstation Overview (6:59)
4.2 How to install the android cargo groundstation application (2:59)
4.3 How to use the android cargo groundstation application and start a mission (8:44)
4.4 Config file (JSON-format) for the android groundstation application (1:36)
4.5 How to load a cargo mission file to the android cargo groundstation application (2:04)
4.6 How to access the logs from the android cargo groundstation application (1:18)
4.7 How to get the IP address of the cargo extension on the drone using an android tablet (1:07)
4.8 How to access the cargo onboard controller file system using an android tablet (1:33)
4.9 How to upload a cargo mission file from the tablet to the onboard cargo extension (1:06)
4.10 How to access the logs of the cargo extension on the drone (0:49)
4.11 How to adjust the country-specific operator identifier of the APN network for the 4G module (1:47)
4.12 How to configure settings for the web server (1:34)
Module 4 Discussion
Course Assignment #2
Module 5 - Mission Planning
Module 5 Overview (1:02)
5.1 Route Planning Introduction (2:49)
5.2 Determining route, waypoints and safe landing locations (4:22)
5.3 QGroundControl Reference Guide
5.4 Mission planning with QGroundControl - Dummy mission (11:52)
5.5 Mission planning with QGroundControl - Real-world mission (9:22)
5.6 Mission planning with QGroundControl - Adjusting mission parameters (3:51)
Module 5 Discussion
Course Assignment #3
Module 6 - Standard Operating Procedures
Module 6 Overview (1:08)
6.1 Pack list - Let's go flying! (3:43)
6.2 Piloting the drone using the DJI Remote Controller (3:17)
6.3 Piloting the drone using virtual joysticks (4:09)
6.4 Mount the cargo box in the field (1:39)
6.5 Mount and test the precision landing setup in the field (3:18)
6.6 Checklist before flying a mission (3:02)
6.7 SOP - Run a Cargo Mission (8:20)
6.8 Failure handling
Module 6 Discussion
Course Assignment #4
Course Evaluation
We welcome your feedback
3.5 Hardware setup - How to mount the cargo loading box
Lesson content locked
If you're already enrolled,
you'll need to login
.
Enroll in Course to Unlock